Quay Point Plastering
Tanking Failure Causes: Why Basement Tanking Stops Working
All articles

Tanking Failure Causes: Why Basement Tanking Stops Working

13 min read

Tanking Failure Causes: Why Basement Tanking Stops Working

Blistered tanking coating on a cellar wall

Tanking usually fails for one of a few reasons: the water pressure behind it was underestimated, the ground water was never drained away, the system was damaged or badly applied, or the moisture was never coming through the wall in the first place. Replacing the coating without finding which of these applies is how damp returns a second time. A survey-led diagnosis, with written findings before any work is proposed, is the way to stop that cycle. That is how we approach every cellar and basement we are asked to look at.

This guide is for homeowners, landlords and property managers whose cellar or basement was tanked and is damp again, or who are about to have it tanked and want to know what to check.

Quaypointplastering
Find the Cause Before Repairing
Quay Point Plastering investigates damp and timber problems through visual assessment, then provides documented findings and a defined scope of work.
Visit

TL;DR

  • Tanking is a below-ground waterproofing system, and it fails mainly through unexpected water pressure, poor drainage, damage or poor application, and lack of maintenance.
  • Professional guidance assumes water may bear on the full height of a below-ground structure at some point in its life, so the design has to allow for it.
  • Leaking gutters, raised ground levels, plumbing leaks and condensation can all look like tanking failure. They need ruling in or out first.
  • Drained systems with pumps and channels need regular servicing, with a first service usually within three to six months.
  • Before any repair, ask for a whole-building inspection with documented findings, not a moisture meter reading alone.

Table of Contents

What tanking is and why it matters which type you have

Tanking means waterproofing the inside or outside of a below-ground wall and floor so that water in the ground cannot reach the living space. In the UK, below-ground waterproofing is described by the Property Care Association (PCA) as three types. Type A is a barrier system, such as a coating or membrane applied to the structure. Type B is the structure itself, such as watertight concrete. Type C is a drained cavity system that lets water in behind a membrane and carries it to a drain or sump.

The type matters because each fails differently. A barrier system fails where water pressure finds a weak point. A drained system fails when the water stops flowing freely. The causes below are grouped that way.

Cause 1: the water pressure was underestimated

Water in the soil pushes against a basement wall and floor. This force is called hydrostatic pressure. The PCA’s Type A waterproofing guidance says a site investigation is important and that water should be assumed to bear against the full height of the below-ground structure at some point in its life. It also says high water tables present the greatest risk of waterproofing failure.

In practice, this goes wrong in a few ways:

  • The basement was assessed in a dry summer, when the ground held less water than it does after a wet winter.
  • A variable water table was designed for its average level rather than its highest. The PCA guidance says it should be designed for the highest.
  • Something changed after the work: a neighbouring development, new paving, or altered drainage sent more water towards the building.

If your damp came back after the first wet season, water pressure is the first thing to investigate. Our guide to the 0.25 m high water table survey check explains how that is assessed on site.

Cause 2: drainage around the structure was missing or has failed

The PCA warns that where a Type A tanked structure has no proper, maintainable drainage around it, hydrostatic pressure can build and cause leakage wherever there is a defect in the waterproofing or concrete. It recommends measures such as geocomposite drainage sheets, fins or land drains to deflect and drain the water.

That makes everything above ground part of the diagnosis. The PCA’s groundwater management guidance and the RICS consumer guide on damp and mould between them point to the same set of culprits:

  • leaking or blocked gutters and rainwater pipes
  • failed underground drainage
  • leaking water main supply pipes
  • raised ground levels next to walls
  • a high local water table or flooding
  • internal plumbing leaks

A tanking system can be well applied and still be overwhelmed if roof water is discharging against the wall. We cover the two most common of these in leaking gutters and damp and ground levels causing damp.

An engineering article from the US, published by IIBEC, makes the same point from a different country. It says below-ground leaks frequently follow an unanticipated rise in hydrostatic pressure, from causes such as runoff from paved areas, regrading, leaking sewers or area drains, obstructed drains and undersized or clogged gutters.

Cause 3: the wrong system for the conditions

A barrier coating suits some conditions and not others. Where water pressure is a real and continuing factor, a drained cavity approach is designed to manage the water rather than resist it. The PCA’s Type A guidance itself notes that a geocomposite drainage sheet can reduce or eliminate hydrostatic pressure on the membrane, which shows how closely the choice of system and the water conditions are linked.

This is why we do not decide the product before the survey. Cellar tanking and cavity-drain membranes are both on our basement and cellar waterproofing page, and which suits a property depends on what the inspection finds, not on a preferred product.

Cause 4: damage during construction and poor application

A waterproofing layer only works if it is continuous and intact. The PCA’s Type A guidance requires membranes to be protected from construction damage. That means vertical blockwork and a 50 mm screed on horizontal surfaces, or rot-proof protection boards.

Things that commonly go wrong at this stage include:

  • the membrane is punctured or torn before it is covered
  • protection is left out or applied late
  • junctions between wall and floor, and pipe or cable penetrations, are not sealed continuously
  • the substrate is poorly prepared, so the coating does not bond

These faults are hidden once the finishes go on, which is why a failure can show up months later as a damp patch some distance from the actual defect. Written findings and dated photographs of each stage give you a record of what was done and where.

Cause 5: blocked or unserviced drained systems

A Type C system relies on water moving. The PCA’s groundwater guidance states that its effectiveness depends on uninterrupted flow, and that any blockage in the membrane cavities, drainage channels, pipes or sump leads to system failure. It lists three typical sources of blockage:

  • silt and fines
  • calcium carbonate (free lime) deposits, especially in new concrete or chalky soils
  • construction debris or poor installation

The same guidance says the first service of a drained system is usually within three to six months, that servicing should be by trained, competent engineers with access to the original plans, and that pump checks should cover main and backup pumps, battery condition, switchgear, seals, washers and valves. Electrical and alarm checks should be done by a qualified electrician. It adds that long-term success depends on regular maintenance, as emphasised in BS 8102:2022. The PCA’s older Type C guidance adds that sumps must be cleared out and tested, and notes the system is most prone to limescale in its early period.

If your cellar has a sump and pump, ask when it was last serviced. A pump that has stopped, or a sump that has silted up, can look exactly like a tanking failure. Our tag page on sump pump maintenance gathers related guidance.

Silt in a cellar sump beside its pump

Cause 6: it was never a tanking problem

Not every damp patch in a basement is water coming through the wall. The IIBEC article notes that some stains are condensation or leaks from overhead pipes rather than infiltration, and that circular stains can indicate condensation. Cellars are cool, often poorly ventilated, and warm moist air meets cold surfaces easily.

The PCA’s Code of Practice on the control of dampness in buildings (January 2023) is clear on why this matters. Moisture meters give only comparative readings in masonry, can be affected by salts, and cannot tell you where the moisture came from. The Code requires a whole-house inspection covering location, structure, materials, maintenance, thermal performance, ventilation and occupation, so that all potential causes are considered.

So a high meter reading on a tanked wall is a reason to investigate, not a diagnosis. Our guide to telling rising, penetrating or condensation damp shows how the patterns differ.

What is the most common cause of basement leaks?

Water pressure from the ground is the most common cause cited in technical guidance, usually combined with a drainage or maintenance fault. The IIBEC article lists a rise in hydrostatic pressure as a frequent cause of below-ground leaks, and the PCA places high water tables at the top of its risk list.

To tell this apart from a failed coating, look at the pattern:

What you see Points towards
Wet at the base of walls and the floor joint, worse after heavy rain Ground water pressure or failed drainage
Wet in one patch, below a gutter or downpipe outside Rainwater goods or ground levels
Damp near bathroom or kitchen pipework above Plumbing leak
Circular or mould-speckled patches on cool surfaces, worse in winter Condensation
Water pooling or an alarm sounding in a sump Pump or drainage failure

A table cannot replace an inspection, but it shows why the same symptom can have different causes.

How to investigate before you repair again

The sequence below is the one that stops a second failed repair.

  1. Gather the history. Collect any survey, guarantee, drawings and repair records. The IIBEC method starts with reviewing reports, construction documents, water-infiltration history and earlier repairs.
  2. Record what you can see. Note where it is wet, when it gets worse, and any flood-level lines, cracks, joints and penetrations. Photograph them with dates.
  3. Check the outside. Look at gutters, downpipes, gullies, paving falls and ground levels against the wall. These are the first items on the RICS list of causes.
  4. Rule out plumbing and condensation. Internal leaks and condensation can mimic ingress.
  5. Get a whole-building inspection. The RICS consumer guide recommends a survey compliant with the JPS 2022 standard from a specialist building surveyor, and the PCA Code asks for the whole-house approach described above.
  6. Fix obvious defects first, then reassess. The IHBC’s JPS 2022 guidance on investigating moisture says dealing with damp is often staged: tackle obvious defects such as ventilation and ground levels, allow time for evaporation, then reassess before moving to other treatments.
  7. Only then agree the remedial scope, in writing, with what each item is meant to achieve.

Where a structural question arises, such as movement or masonry condition, a structural input may be needed first. We say so rather than stretch beyond what we do.

Our approach to a failed or doubtful tank

Our approach to a failed or doubtful tank

We specialise in survey-led damp, mould and timber work across Dorset, Hampshire and Wiltshire, with over 35 years in the industry. The survey comes first: we diagnose from the visible symptoms, give you written findings and a defined scope of work, and treat only after that inspection. Our work is backed by written guarantees on workmanship, and we use original project photography so you can see what was done.

For a tanked cellar that is damp again, that means looking at the water sources, drainage and ventilation as well as the wall. Our basement waterproofing service covers cellar tanking and cavity-drain membranes, and our leak detection and plumbing repair work covers the case where the water is coming from a pipe. Where something sits outside our remit, we refer you to the right specialist.

Quaypointplastering

If your basement is damp after tanking, book an inspection through our website or call 01202 287134. Tell us what you can see, when it appears and what has been done before, and we will tell you what we need to check.

Our view

A failed tank is rarely a single bad product. It is usually a gap in the diagnosis: the water was assessed in the wrong season, the roof water was left to run down the wall, or the drained system was never serviced. The coating or membrane gets the blame because it is the part you can see.

That is why we begin with a survey and write down what we find before proposing any treatment. A defined scope, with photographs and a written guarantee, means you know what is being done, why, and what it is meant to achieve. It also lets you compare any later change in the building against a record rather than memory.

When a basement is damp again, the useful question is not which coating to apply next. It is where the water is coming from, and whether the system in place was designed for that water.

Quay

FAQ

Will tanking stop damp?

Tanking is designed to keep ground water out of a below-ground space, and it works when it suits the water conditions and is installed and maintained properly. It does not address damp from other sources such as condensation, leaking gutters or plumbing. A survey identifies which sources are present before any system is chosen.

Why is damp returning after tanking?

The usual reasons are unexpected water pressure, missing or blocked drainage, damage to the waterproofing layer, or a moisture source that was never tanking related. The IHBC guidance suggests fixing obvious defects first and reassessing after a period of drying. A whole-building inspection with written findings is the safest way to find which applies.

How often should a drained basement system be serviced?

The PCA’s groundwater guidance says the first service of a drained system is usually within three to six months. After that, servicing should be regular and carried out by trained, competent engineers who have access to the original plans. Pump, battery, valve and alarm checks form part of that service.

Can a moisture meter tell me why tanking has failed?

No. According to the PCA Code of Practice, meter readings in masonry are only comparative, can be skewed by salts and cannot identify the source of moisture. They are a starting point for the inspection, which should look at the whole building.

Sources

Call nowFree survey